Gigabit 48-volt Passive POE Injector

POE-48-0.5A-G

Gigabit 48-volt Passive POE Injector

Type G 3-Pin power supply

POE-48-0.5A-G

Write your review

Gigabit 48-volt Passive POE Injector

POE-48-0.5A-G

Gigabit 48-volt Passive POE Injector

Type G 3-Pin power supply

Write your review

16 other products in the same category

Outdoor Gigabit PoE Extender

Brands: Tycon Systems

POE-EXT-GD-HP

The POE-EXT-GD-HP is a high quality, high power, shielded Gigabit Ethernet and PoE extender to be able to extend Ethernet beyond the standard 100m limit. By using multiple units, Ethernet and PoE can be extended up to 300m over CAT5/CAT6 cables. The units are powered by PoE so no additional power source is required. Units can accept Mode A (Pins 1,2,3,6) or Mode B (Pins 4,5,7,8) PoE: 802.3af, 802.3at or 48V Passive PoE.

The rugged outdoor weatherproof enclosures are powder coated aluminum and are rated to IP66. The units meet outdoor temperature ratings of -25C to +55C.

DATA SHEET

Passive PoE Power Tap Adapter

Brands: Tycon Systems

POE-PowerTap

Taps into passive PoE power on RJ45 connectors and outputs to a wire terminal connection. Pins 4,5 and 7,8. Can also be used to inject power.

Tycon Power Systems

The POE-PowerTap is a unique tool that allows monitoring or testing of PoE voltages, Extracting PoE voltage from a PoE switch or injector or Injecting PoE voltages to a CAT5 cable. The POE-PowerTap is outfitted with a wire terminal connector for up to 12awg wire.

DATA SHEET

802.3af/at Gigabit PoE Converter, 18/24V Passive PoE Out

Brands: Tycon Systems

TP-POE-1824G

48V 802.3af/at Gigabit input, Switch Selectable 18V or 24V 24W Gigabit passive PoE output. Converts 802.3af/at PoE to passive PoE.

The TP-POE-1824G Power Over Ethernet 802.3af/at converter is a unique product allowing a customer to run a Passive PoE device from a standard 802.3af or at PoE switch. They accept 802.3af/at PoE in and provide a switch selectable 24W PoE output of 18VDC or 24VDC.

DATA SHEET

BreezePro® 400W 12V/24V Horizontal Wind Turbine

Brands: Tycon Systems

TPW-400DT-12/24

The BreezePro® Wind Turbines from Tycon Solar® are lightweight at less than 10.5kg and are designed for ease of installation and long service life. The generator is a very low cogging force design for better performance in light winds and is packaged in a fully sealed die cast aluminum enclosure. There are no brushes to wear out or cause electrical noise and the bearings are sealed so the system is maintenance free. The blades are glass reinforced nylon for high strength, UV resistance and fatigue resistance. The turbines are 12V/24V auto voltage select.

DATA SHEET

4 Port Gigabit Midspan Injector, DC

Brands: Tycon Systems

TP-MS4X4

Gigabit Mid Span, High Power 1A per port, Univolt PoE Injector - 4 PoE output ports with the same or different PoE voltage.

Features

- High Power, Gigabit 4 Port Midspan POE Injector

- Up to 1A per Individual Port

- Universal PoE Voltage 12VDC to 57VDC.

- Surge Protection on Data Inputs.

- Supports Different PoE Voltage on Each Port. 

- Supports Reverse Voltage on Individual Ports.

- Powers 802.3af and Passive PoE Devices.

DATA SHEET

Dual USB to 24V Passive PoE Inserter

Brands: Tycon Systems

TP-DCDC-2USB-24

USB Powered 24V Passive PoE inserter. 24VDC 12W Passive PoE Output with 2 USB power inputs. 10/100Mb.

The TP-DCDC-2USB-24 Passive Power Over Ethernet Power Source offered by Tycon Power Systems is a unique 24VDC Passive POE injector powered by two USB ports. They work by supplying power to the remote device on the 4 unused Ethernet pins 4,5(+) and 7,8(-). The Ethernet spec supports distances up to 100m (328 feet).

DATA SHEET

8 Port 10/100Mb 802.3af/at PoE Switch

Brands: Tycon Systems

TP-SW8-D

The TP-SW8-D Power over Ethernet 802.3af/at (PoE) 10/100Mb switch offered by Tycon Power® is a fully automatic high speed 8 port Ethernet switch. TP-SW8- D has a 2 channel 802.3at input for 70W max PoE input. Both models supply power to the remote device on the unused Ethernet pins 4,5(V+) and 7,8(V-).

DATA SHEET

24VDC to 56VDC 70W DCDC Voltage Converter

Brands: Tycon Systems

TP-VRHP-2456

Voltage Converter 18-36VDC Input, 56VDC @ 1.5A 70W Regulated output. 

The TP-VRHP-2456 is a 70W voltage converter/regulator which accepts an input of plus or minus +/-18VDC to 36VDC and provides a regulated output of 56VDC @ 1.25A 70W. These units are perfect for providing 56VDC voltage from -24VDC telecom power. Input and outputs are wire terminals for wire up to 12AWG. Operates from -30 to +65 deg C (-22 deg F to 149 deg F). 

DATA SHEET

12/24VDC In, 18V Passive PoE Inserter

Brands: Tycon Systems

TP-DCDC-1218

9-36VDC IN, 18V 18W Passive PoE OUT, DC to DC Converter/PoE inserter. 10/100Mb.

The TP-DCDC-1218 DC to DC converters offered by Tycon Power Systems are a low cost and high reliability solution for those requiring 18VDC Power Over Ethernet voltage from a 12 or 24V battery system. 

They have an integrated PoE injector to apply the regulated 18VDC to the CAT5 Ethernet cable. The input voltage must be between 9VDC and 36VDC.

DATA SHEET

3 Port Gigabit PoE Switch/Extender IEEE802.3af/at

Brands: Tycon Systems

TP-SW3G

The TP-SW3G Power over Ethernet (PoE) 3 Port Gigabit switches offered by Tycon® are fully automatic high speed Ethernet switches with up to 30W of PoE power per port.

The unit accepts Gigabit data and power via PoE into the RJ45 “PoE In” port. The PoE In port is compatible with IEEE802.3af, IEEE802.3at and IEEE802.3at 4 pair (60W). It can also accept 42-57VDC Passive PoE.

There are two fully compliant 802.3af/at Gigabit “PoE Out” ports. These ports are capable of up to 30W per port and 100m (330ft) distance.

DATA SHEET

48V 240W DIN Rail Industrial Power Supply

Brands: Tycon Systems

PSDIN-48-240W

The PSDIN Series of Industrial DIN Rail mount high efficiency switching power supplies operate over a wide temperature range of -40C to +70C. There are two models to supply 120W or 240W. The input is 90 to 264VAC auto-ranging with wire terminal connections. The output is 48VDC nominal with an adjustment range from 47VDC to 56VDC. There is a switch for single or parallel operation. Two 240W supplies operating in parallel will provide 480W total power. There is an alarm output to provide a dry contact closure to trigger an alarm if the DC output fails, like during a grid power failure. The relay is closed when DC output is normal and open when DC output is in fault condition due to overload or safety shutdown.

DATA SHEET

5 Port 10/100Mb Passive PoE Switch

Brands: Tycon Systems

TP-SSW5-NC

Universal Voltage 10/100 PoE Switch. Switch accepts universal voltage (12-57VDC) via the wire terminal connector on the back of the Switch. This model is very compact at only 4”x5”x1.5”. 2A per port.

On the universal voltage models (“-NC”) the PoE output voltage = the input voltage so it is universal in its application. The Ethernet spec supports distances up to 100m (328 feet) between the PoE switch and the remote device.

Tycon Power® sells a variety of power supplies in 60W, 120W and 180W sizes. 18VDC, 24VDC and 48VDC are available. All the Switches have DIN Rail mounts included for convenient DIN rail mounting.

DATA SHEET

10-15VDC IN 24VDC OUT 35W Hi Power DC to DC Converter and PoE inserter

Brands: Tycon Systems

TP-DCDC-1224-HP

The TP-DCDC-HP Series of DC to DC converters offered by Tycon Power® are a low cost and high reliability solution for those requiring 24VDC or 56VDC Power over Ethernet voltage from a 12V, 24V or 48V battery system. They have an integrated PoE injector. Passive PoE and 802.3at models are available.

The input and output are isolated so the units can accept minus voltage on input and can be wired for positive voltage on the output for those systems which are negative voltage based.

If the remote device does not support power over Ethernet, splitters (POE-SPLT-S) are available to split the data and DC voltage at the remote device. If the remote device requires reverse voltage the POE-XOVER-S cable can be used.

DATA SHEET