10-15VDC IN 24VDC OUT 35W Hi Power DC to DC Converter and PoE inserter

10-15VDC IN 24VDC OUT 35W Hi Power DC to DC Converter and PoE inserter

TP-DCDC-1224-HP

The TP-DCDC-HP Series of DC to DC converters offered by Tycon Power® are a low cost and high reliability solution for those requiring 24VDC or 56VDC Power over Ethernet voltage from a 12V, 24V or 48V battery system. They have an integrated PoE injector. Passive PoE and 802.3at models are available.

The input and output are isolated so the units can accept minus voltage on input and can be wired for positive voltage on the output for those systems which are negative voltage based.

If the remote device does not support power over Ethernet, splitters (POE-SPLT-S) are available to split the data and DC voltage at the remote device. If the remote device requires reverse voltage the POE-XOVER-S cable can be used.

DATA SHEET

TP-DCDC-1224-HP

Write your review

10-15VDC IN 24VDC OUT 35W Hi Power DC to DC Converter and PoE inserter

TP-DCDC-1224-HP

The TP-DCDC-HP Series of DC to DC converters offered by Tycon Power® are a low cost and high reliability solution for those requiring 24VDC or 56VDC Power over Ethernet voltage from a 12V, 24V or 48V battery system. They have an integrated PoE injector. Passive PoE and 802.3at models are available.

The input and output are isolated so the units can accept minus voltage on input and can be wired for positive voltage on the output for those systems which are negative voltage based.

If the remote device does not support power over Ethernet, splitters (POE-SPLT-S) are available to split the data and DC voltage at the remote device. If the remote device requires reverse voltage the POE-XOVER-S cable can be used.

DATA SHEET

Write your review

16 other products in the same category

Brands: Tycon Systems

TP-SW8-D

The TP-SW8-D Power over Ethernet 802.3af/at (PoE) 10/100Mb switch offered by Tycon Power® is a fully automatic high speed 8 port Ethernet switch. TP-SW8- D has a 2 channel 802.3at input for 70W max PoE input. Both models supply power to the remote device on the unused Ethernet pins 4,5(V+) and 7,8(V-).

DATA SHEET

Brands: Tycon Systems

TP-SW8G-2SFP

The TP-SW8G-2SFP Power over Ethernet (PoE) 10 port Gigabit switch offered by Tycon® is a fully automatic high speed Layer 2+ Ethernet manageable switches. The 10 port model has 8 PoE + 2 SFP ports. The PoE ports are Mode A (pins 1,2,3,6) type and are manageable via the user interface. They can be set to PoE, PoE+ or OFF. Default is PoE+.

The switch features security protocols like SSH and SSL for secure access of the switch command interface. The interface can be accessed via the serial console port or any of the Ethernet ports. The command interface can be controlled via web browser, command line interface(CLI), TELNET, SSH or SNMP.

DATA SHEET

Brands: Tycon Systems

TP-SW5G-VERSA

The TP-SW5G-VERSA Power over Ethernet (PoE) 5 Port Gigabit switch offered by Tycon® is a fully automatic high speed Layer 2 Ethernet switches with multiple function ports. Port 1 is a 60W 4pair High PoE port; Port 2,3,4 are 48V 30W 802.3at compatible ports; Port 5 is a 24V 12W Passive PoE port. This allows a customer to power up multiple PoE devices with different power requirements. The switch requires a 48-56VDC (4A) power input.

DATA SHEET

Brands: Mikrotik

RBGPOE

PoE injector, for Gigabit LAN products

The new MikroTik Gigabit PoE adapter for powering any RouterBOARD over Gigabit Ethernet. Simply connect your power source and then use an ethernet cable to connect the injector to the RouterBOARD device.

For using with any RouterBOARD that supports 9-48V PoE. 

The GPOE has shielded connectors.

DATA SHEET

Brands: Tycon Systems

TP-VRHP-2424

Voltage Converter 18-36VDC Input, 24VDC @ 2.9A 70W Regulated output. 

he TP-VRHP-2424 is a 70W voltage converter/regulator which accepts an input of plus or minus 18VDC to 36VDC and provides a regulated output of 24VDC @ 2.9A 70W. These units are perfect for providing stable regulated 24VDC voltage from 24VDC battery banks. Input and outputs are wire terminals for wire up to 12AWG. Operates from -30 to +65 deg C.

DATA SHEET

Brands: Tycon Systems

TP-DCDC-4848D-HP

+/- 36-72VDC IN, 56VDC OUT 802.3at 35W High Power DC to DC Converter/PoE+ inserter. 10/100Mb.

The TP-DCDC-4848D-HP DC to DC converters offered by Tycon Power Systems are a low cost and high reliability solution for those requiring 48VDC Power Over Ethernet voltage from a +/-48V battery system. 

The PoE inserters are 802.3af/at compatible. 

They have an integrated 10/100Mb PoE+ injector to apply the regulated 56VDC to the CAT5 Ethernet cable. The input voltage must be between 36VDC and 72VDC.

DATA SHEET

Brands: Ubiquiti

USP-RPS

The UniFi SmartPower Redundant Power System, model USP-RPS, is a proprietary redundant power system designed to protect up to six UniFi SmartPower supported devices from sudden power supply module failure.

The USP-RPS continually monitors all attached devices. In the event of an internal AC/DC power supply failure, failover is automatic so your network continues to operate with no interruption in service. With a 950W DC power budget, the USP-RPS can protect a variety of high-power devices, including UniFi PoE switches. An integrated 1.3" color touchscreen LCM displays system information for convenient monitoring.

DATA SHEET

Brands: Tycon Systems

TP-SW5G-24

The SW5 Series Power over Ethernet (PoE) switches offered by Tycon Power® are fully automatic high speed 5 port Ethernet switches with up to 2A of PoE power per port.

IEEE802.3af/at Compliant 48VDC 10/100/1000MB PoE Switch. Switch accepts 12-36VDC power via a wire terminal connector on the back of the Switch or via 48VDC PoE into the 802.3af/at compliant uplink port (90W max). Perfect for remote solar/battery systems. 35W per port. 70W Max Total.

On the universal voltage models (“-NC”) the PoE output voltage = the input voltage so it is universal in its application. The Ethernet spec supports distances up to 100m (328 feet) between the PoE switch and the remote device.

DATA SHEET

Brands: Tycon Systems

TP-DCDC-1256G-VHP Gigabit 10-60VDC IN 56VDC OUT 70W 4 Pair Hi Power DC to DC Converter and passive PoE inserter. Ubiquiti airFiber™ DATA SHEET

TP-DCDC-1256GD-VHP Gigabit 10-60VDC IN 56VDC OUT 70W 4 Pair Hi Power DC to DC Conv and 802.3at PoE inserter. For Axis Q60 series PTZ cameras. UPOE Compatible. DATA SHEET

TP-DCDC-1256GD-BT Gigabit 10-60VDC IN 56VDC OUT 70W 4 Pair Hi Power DC to DC Conv and 802.3bt PoE inserter. DATA SHEET

Brands: Tycon Systems

TP-VRHP-1224

Voltage Converter 10-15VDC Input, 24VDC @ 3A 70W Regulated output. 

The TP-VRHP-1224 is a 70W voltage converter/regulator which accepts an input of plus or minus 10VDC to 15VDC and provides a regulated output of 24VDC @ 1.25A 70W. These units are perfect for providing 24VDC voltage from 12VDC battery source like in a vehicular application or remote power application. Input and outputs are wire terminals for wire up to 12AWG. Operates from -30 to +65 deg C.

DATA SHEET

Brands: Tycon Systems

TP-VRHP-4824

Voltage Converter 36-72VDC Input, 24VDC @ 2.5A 70W Regulated output. 

The TP-VRHP-4824 is a 70W voltage converter/regulator which accepts an input of 36VDC to 72VDC and provides a regulated output of 24VDC @ 3A 70W. Input and outputs are wire terminals for wire up to 12AWG. Operates from -30 to +65 deg C. 

DATA SHEET

Brands: Tycon Systems

TP-SSW5-NC

Universal Voltage 10/100 PoE Switch. Switch accepts universal voltage (12-57VDC) via the wire terminal connector on the back of the Switch. This model is very compact at only 4”x5”x1.5”. 2A per port.

On the universal voltage models (“-NC”) the PoE output voltage = the input voltage so it is universal in its application. The Ethernet spec supports distances up to 100m (328 feet) between the PoE switch and the remote device.

Tycon Power® sells a variety of power supplies in 60W, 120W and 180W sizes. 18VDC, 24VDC and 48VDC are available. All the Switches have DIN Rail mounts included for convenient DIN rail mounting.

DATA SHEET