TP-DCDC-1248Dx2-HP 10-15VDC IN, Qty 2 Ports 802.3af/at 56VDC 21W OUT DC to DC Converter and PoE inserter. DATA SHEET
TP-DCDC-1248G-HP 10-15VDC IN 56VDC OUT 50W Hi Power DC to DC Converter and PoE inserter, LVD Function. DATA SHEET
TP-DCDC-1248GD-HP Gigabit 10-15VDC IN 56VDC OUT 35W Hi Power DC to DC Converter and 802.3at PoE inserter. DATA SHEET
TP-MS4X4
Gigabit Mid Span, High Power 1A per port, Univolt PoE Injector - 4 PoE output ports with the same or different PoE voltage.
Features
- High Power, Gigabit 4 Port Midspan POE Injector
- Up to 1A per Individual Port
- Universal PoE Voltage 12VDC to 57VDC.
- Surge Protection on Data Inputs.
- Supports Different PoE Voltage on Each Port.
- Supports Reverse Voltage on Individual Ports.
- Powers 802.3af and Passive PoE Devices.
TP-DCDC-4824G
The TP-DCDC Gigabit Series of DC to DC converters offered by Tycon Power® are a low cost and high efficiency solution for those requiring IEEE802.3af or Passive Power over Ethernet from a 12VDC or 24VDC or 48VDC voltage source like a battery system or vehicle. They have an integrated POE injector to apply the power and data output to the CAT5 Ethernet cable. The output voltage is regulated and protected. They have two isolated inputs for connecting 2 power sources, like a primary and backup power source. A metal enclosure model is available for industrial applications.
PSDIN-48-240W
The PSDIN Series of Industrial DIN Rail mount high efficiency switching power supplies operate over a wide temperature range of -40C to +70C. There are two models to supply 120W or 240W. The input is 90 to 264VAC auto-ranging with wire terminal connections. The output is 48VDC nominal with an adjustment range from 47VDC to 56VDC. There is a switch for single or parallel operation. Two 240W supplies operating in parallel will provide 480W total power. There is an alarm output to provide a dry contact closure to trigger an alarm if the DC output fails, like during a grid power failure. The relay is closed when DC output is normal and open when DC output is in fault condition due to overload or safety shutdown.
TP-VRHP-1256
Voltage Converter 10-15VDC Input, 56VDC @ 1.25A 70W Regulated output.
The TP-VRHP-1256 is a 70W voltage converter/regulator which accepts an input of plus or minus 10VDC to 15VDC and provides a regulated output of 56VDC @ 1.25A 70W. These units are perfect for providing 56VDC voltage from 12VDC battery source like in a vehicular application or remote power application. Input and outputs are wire terminals for wire up to 12AWG. Operates from -30 to +65 deg C.
TP-VRHP-4824
Voltage Converter 36-72VDC Input, 24VDC @ 2.5A 70W Regulated output.
The TP-VRHP-4824 is a 70W voltage converter/regulator which accepts an input of 36VDC to 72VDC and provides a regulated output of 24VDC @ 3A 70W. Input and outputs are wire terminals for wire up to 12AWG. Operates from -30 to +65 deg C.
MTP250-26V94-OD
Outdoor IP67 26V 250W AC/DC power supply units for the MikroTik NetPower 16P. Built for situations when your outdoor switches need that extra juice. Pole/wall mount compatible!
POE-24-24W
PoE Injector, 24VDC, 24W
PoE Adapters power Ubiquiti products that support passive PoE.
POE-24-1A-G
Gigabit 24-volt Passive POE Injector
Type G 3-Pin power supply
TP-DCDC-4824-HP 36-72VDC IN 24VDC OUT 30W Hi Power DC to DC Converter and PoE inserter. DATA SHEET
TP-DCDC-4824G-HP Gigabit 36-72VDC IN 24VDC OUT 30W Hi Power DC to DC Converter and Passive PoE inserter.
ETH-SP-G2
Ethernet Surge Protector, Gen 2
The ETH-SP is engineered to protect any Power‑over‑Ethernet (PoE) or non‑PoE device with connection speeds of up to 1 Gbps.
TP-SW5GD-BT
The TP-SW5GD-BT Power over Ethernet (PoE) 5 Port Gigabit switch offered by Tycon® is a fully automatic high speed Layer 2 Ethernet switch with one 802.3bt PoE input and four 802.3at PoE outputs. Ports 1-4 are 802.3at 35W PoE Out. The Uplink Port 5, is 802.3bt compatible so the switch can accept up to 100W PoE on 4 pairs to power the switch and connected devices remotely over CAT5 or higher Ethernet Cable. The Ethernet spec supports distances up to 100m (328ft). By using as a repeater, 200m total distance is realistic.
The switch can accept power via three different interfaces: Wire Terminal Connector, 4 pin Mini DIN connector or via 802.3at/bt PoE input to Uplink Port 5. Two different power inputs can be used for redundancy. The higher voltage takes priority.
TP-DCDC-2424GR-VHP
The Gigabit compatible TP-DCDC-2424GR-VHP are special very high power DC to DC converters / PoE inserters designed especially for Ubiquiti airFiber x™ wireless radio systems and other systems which require high power passive PoE (High PoE). The unique PoE inserter supplies 24VDC PoE power on all 8 Ethernet wires (4 pair) with the following pinout: 1,2,4,5 V+ and 3,6,7,8 V
They have two isolated inputs for connecting 2 power sources, like a primary and backup power source. They have various protections for surge, short circuit and overload. The input and output are isolated.
TP-SW3G
The TP-SW3G Power over Ethernet (PoE) 3 Port Gigabit switches offered by Tycon® are fully automatic high speed Ethernet switches with up to 30W of PoE power per port.
The unit accepts Gigabit data and power via PoE into the RJ45 “PoE In” port. The PoE In port is compatible with IEEE802.3af, IEEE802.3at and IEEE802.3at 4 pair (60W). It can also accept 42-57VDC Passive PoE.
There are two fully compliant 802.3af/at Gigabit “PoE Out” ports. These ports are capable of up to 30W per port and 100m (330ft) distance.
USP-RPS
The UniFi SmartPower Redundant Power System, model USP-RPS, is a proprietary redundant power system designed to protect up to six UniFi SmartPower supported devices from sudden power supply module failure.
The USP-RPS continually monitors all attached devices. In the event of an internal AC/DC power supply failure, failover is automatic so your network continues to operate with no interruption in service. With a 950W DC power budget, the USP-RPS can protect a variety of high-power devices, including UniFi PoE switches. An integrated 1.3" color touchscreen LCM displays system information for convenient monitoring.
TP-SW5G-24
The SW5 Series Power over Ethernet (PoE) switches offered by Tycon Power® are fully automatic high speed 5 port Ethernet switches with up to 2A of PoE power per port.
IEEE802.3af/at Compliant 48VDC 10/100/1000MB PoE Switch. Switch accepts 12-36VDC power via a wire terminal connector on the back of the Switch or via 48VDC PoE into the 802.3af/at compliant uplink port (90W max). Perfect for remote solar/battery systems. 35W per port. 70W Max Total.
On the universal voltage models (“-NC”) the PoE output voltage = the input voltage so it is universal in its application. The Ethernet spec supports distances up to 100m (328 feet) between the PoE switch and the remote device.
TP-DCDC-1248Dx2-HP 10-15VDC IN, Qty 2 Ports 802.3af/at 56VDC 21W OUT DC to DC Converter and PoE inserter. DATA SHEET
TP-DCDC-1248G-HP 10-15VDC IN 56VDC OUT 50W Hi Power DC to DC Converter and PoE inserter, LVD Function. DATA SHEET
TP-DCDC-1248GD-HP Gigabit 10-15VDC IN 56VDC OUT 35W Hi Power DC to DC Converter and 802.3at PoE inserter. DATA SHEET
