12VDC In, 24V Passive PoE Inserter

12VDC In, 24V Passive PoE Inserter

TP-DCDC-1224 9-36VDC IN 24V PoE OUT 24W DC to DC Converter and PoE inserter DATA SHEET

TP-DCDC-1224G Gigabit 9-36VDC IN 24V PoE OUT 20W DC to DC Converter and PoE inserter DATA SHEET

TP-DCDC-1224G-4P Gigabit 9-36VDC IN 24VDC 4 Pair PoE OUT 24W DC to DC Converter and PoE inserter

Write your review

12VDC In, 24V Passive PoE Inserter

TP-DCDC-1224 9-36VDC IN 24V PoE OUT 24W DC to DC Converter and PoE inserter DATA SHEET

TP-DCDC-1224G Gigabit 9-36VDC IN 24V PoE OUT 20W DC to DC Converter and PoE inserter DATA SHEET

TP-DCDC-1224G-4P Gigabit 9-36VDC IN 24VDC 4 Pair PoE OUT 24W DC to DC Converter and PoE inserter

Write your review

16 other products in the same category

Brands: Tycon Systems

TP-DCDC-1218

9-36VDC IN, 18V 18W Passive PoE OUT, DC to DC Converter/PoE inserter. 10/100Mb.

The TP-DCDC-1218 DC to DC converters offered by Tycon Power Systems are a low cost and high reliability solution for those requiring 18VDC Power Over Ethernet voltage from a 12 or 24V battery system. 

They have an integrated PoE injector to apply the regulated 18VDC to the CAT5 Ethernet cable. The input voltage must be between 9VDC and 36VDC.

DATA SHEET

Brands: Tycon Systems

TP-VRHP-2456

Voltage Converter 18-36VDC Input, 56VDC @ 1.5A 70W Regulated output. 

The TP-VRHP-2456 is a 70W voltage converter/regulator which accepts an input of plus or minus +/-18VDC to 36VDC and provides a regulated output of 56VDC @ 1.25A 70W. These units are perfect for providing 56VDC voltage from -24VDC telecom power. Input and outputs are wire terminals for wire up to 12AWG. Operates from -30 to +65 deg C (-22 deg F to 149 deg F). 

DATA SHEET

Brands: Tycon Systems

PSDIN-48-240W

The PSDIN Series of Industrial DIN Rail mount high efficiency switching power supplies operate over a wide temperature range of -40C to +70C. There are two models to supply 120W or 240W. The input is 90 to 264VAC auto-ranging with wire terminal connections. The output is 48VDC nominal with an adjustment range from 47VDC to 56VDC. There is a switch for single or parallel operation. Two 240W supplies operating in parallel will provide 480W total power. There is an alarm output to provide a dry contact closure to trigger an alarm if the DC output fails, like during a grid power failure. The relay is closed when DC output is normal and open when DC output is in fault condition due to overload or safety shutdown.

DATA SHEET

Brands: Ubiquiti

USP-RPS

The UniFi SmartPower Redundant Power System, model USP-RPS, is a proprietary redundant power system designed to protect up to six UniFi SmartPower supported devices from sudden power supply module failure.

The USP-RPS continually monitors all attached devices. In the event of an internal AC/DC power supply failure, failover is automatic so your network continues to operate with no interruption in service. With a 950W DC power budget, the USP-RPS can protect a variety of high-power devices, including UniFi PoE switches. An integrated 1.3" color touchscreen LCM displays system information for convenient monitoring.

DATA SHEET

Brands: Tycon Systems

TP-POE-1824G

48V 802.3af/at Gigabit input, Switch Selectable 18V or 24V 24W Gigabit passive PoE output. Converts 802.3af/at PoE to passive PoE.

The TP-POE-1824G Power Over Ethernet 802.3af/at converter is a unique product allowing a customer to run a Passive PoE device from a standard 802.3af or at PoE switch. They accept 802.3af/at PoE in and provide a switch selectable 24W PoE output of 18VDC or 24VDC.

DATA SHEET

Brands: Tycon Systems

TP-VRHP-2424

Voltage Converter 18-36VDC Input, 24VDC @ 2.9A 70W Regulated output. 

he TP-VRHP-2424 is a 70W voltage converter/regulator which accepts an input of plus or minus 18VDC to 36VDC and provides a regulated output of 24VDC @ 2.9A 70W. These units are perfect for providing stable regulated 24VDC voltage from 24VDC battery banks. Input and outputs are wire terminals for wire up to 12AWG. Operates from -30 to +65 deg C.

DATA SHEET

Brands: Tycon Systems

TPDIN-MONITOR-WEB2

The TPDIN® Based Remote Monitor and Control System is a versatile tool which enables the equipment designer and installer to remotely monitor their equipment and site. The unit can be accessed via the network (web and SNMP) to remotely monitor up to 4 voltages, 4 currents, 2 temperatures and control power to various equipment using 4 on-board relays. The system has built-in surge protection to prevent damage from electrical surges.

DATA SHEET

Brands: Tycon Systems

TP-DCDC-2424GR-VHP

The Gigabit compatible TP-DCDC-2424GR-VHP are special very high power DC to DC converters / PoE inserters designed especially for Ubiquiti airFiber x™ wireless radio systems and other systems which require high power passive PoE (High PoE). The unique PoE inserter supplies 24VDC PoE power on all 8 Ethernet wires (4 pair) with the following pinout: 1,2,4,5 V+ and 3,6,7,8 V

They have two isolated inputs for connecting 2 power sources, like a primary and backup power source. They have various protections for surge, short circuit and overload. The input and output are isolated.

DATA SHEET

Brands: Tycon Systems

TP-SW8-D

The TP-SW8-D Power over Ethernet 802.3af/at (PoE) 10/100Mb switch offered by Tycon Power® is a fully automatic high speed 8 port Ethernet switch. TP-SW8- D has a 2 channel 802.3at input for 70W max PoE input. Both models supply power to the remote device on the unused Ethernet pins 4,5(V+) and 7,8(V-).

DATA SHEET

Brands: Tycon Systems

TP-VRHP-4856-250

The TP-VRHP-4856-250 DC to DC converter offers high output voltage conversion in a compact metal enclosure. They have wire terminal inputs and outputs for maximum flexibility. The units come with DIN rail adapters for DIN rail mounting. They provide power output up to 250W. 36-72VDC Input, 56V 4.46A 250W Regulated out DCDC Isolated Voltage Converter.

DATA SHEET

Brands: Tycon Systems

TP-SW5G-VERSA

The TP-SW5G-VERSA Power over Ethernet (PoE) 5 Port Gigabit switch offered by Tycon® is a fully automatic high speed Layer 2 Ethernet switches with multiple function ports. Port 1 is a 60W 4pair High PoE port; Port 2,3,4 are 48V 30W 802.3at compatible ports; Port 5 is a 24V 12W Passive PoE port. This allows a customer to power up multiple PoE devices with different power requirements. The switch requires a 48-56VDC (4A) power input.

DATA SHEET

Brands: Tycon Systems

TP-SW4G-2SFP

The TP-SW4G-2SFP Power over Ethernet (PoE) 6 port Gigabit switch offered by Tycon® is a fully automatic high speed Layer 2+ Ethernet manageable switches. The 6 port model has 4 PoE + 2 SFP ports. The PoE ports are Mode A (pins 1,2,3,6) type and are manageable via the user interface. They can be set to PoE, PoE+ or OFF. Default is PoE+.

The switch features security protocols like SSH and SSL for secure access of the switch command interface. The interface can be accessed via the serial console port or any of the Ethernet ports. The command interface can be controlled via web browser, command line interface(CLI), TELNET, SSH or SNMP.

DATA SHEET

Brands: Tycon Systems

TP-SW5G-24

The SW5 Series Power over Ethernet (PoE) switches offered by Tycon Power® are fully automatic high speed 5 port Ethernet switches with up to 2A of PoE power per port.

IEEE802.3af/at Compliant 48VDC 10/100/1000MB PoE Switch. Switch accepts 12-36VDC power via a wire terminal connector on the back of the Switch or via 48VDC PoE into the 802.3af/at compliant uplink port (90W max). Perfect for remote solar/battery systems. 35W per port. 70W Max Total.

On the universal voltage models (“-NC”) the PoE output voltage = the input voltage so it is universal in its application. The Ethernet spec supports distances up to 100m (328 feet) between the PoE switch and the remote device.

DATA SHEET