8 Port 10/100Mb Passive PoE Switch

TP-SW8-NC

The TP-SW8-D Power over Ethernet 802.3af/at (PoE) 10/100Mb switch offered by Tycon Power® is a fully automatic high speed 8 port Ethernet switch.

The -NC version is a passive PoE model for devices which are not 802.3af/at compliant.

On the -NC version the PoE output voltage = the input voltage so it is universal in its application. The DC input power range can be from 12V to 57V. The units can be powered via 2 or 4 pair PoE to port 8 (2A max).

DATA SHEET

TP-SW8-NC

Write your review

8 Port 10/100Mb Passive PoE Switch

TP-SW8-NC

The TP-SW8-D Power over Ethernet 802.3af/at (PoE) 10/100Mb switch offered by Tycon Power® is a fully automatic high speed 8 port Ethernet switch.

The -NC version is a passive PoE model for devices which are not 802.3af/at compliant.

On the -NC version the PoE output voltage = the input voltage so it is universal in its application. The DC input power range can be from 12V to 57V. The units can be powered via 2 or 4 pair PoE to port 8 (2A max).

DATA SHEET

Write your review

16 other products in the same category

Brands: Tycon Systems

TP-SW5G-24

The SW5 Series Power over Ethernet (PoE) switches offered by Tycon Power® are fully automatic high speed 5 port Ethernet switches with up to 2A of PoE power per port.

IEEE802.3af/at Compliant 48VDC 10/100/1000MB PoE Switch. Switch accepts 12-36VDC power via a wire terminal connector on the back of the Switch or via 48VDC PoE into the 802.3af/at compliant uplink port (90W max). Perfect for remote solar/battery systems. 35W per port. 70W Max Total.

On the universal voltage models (“-NC”) the PoE output voltage = the input voltage so it is universal in its application. The Ethernet spec supports distances up to 100m (328 feet) between the PoE switch and the remote device.

DATA SHEET

Brands: Tycon Systems

TP-VRHP-1224

Voltage Converter 10-15VDC Input, 24VDC @ 3A 70W Regulated output. 

The TP-VRHP-1224 is a 70W voltage converter/regulator which accepts an input of plus or minus 10VDC to 15VDC and provides a regulated output of 24VDC @ 1.25A 70W. These units are perfect for providing 24VDC voltage from 12VDC battery source like in a vehicular application or remote power application. Input and outputs are wire terminals for wire up to 12AWG. Operates from -30 to +65 deg C.

DATA SHEET

Brands: Tycon Systems

TP-SW4G-2SFP

The TP-SW4G-2SFP Power over Ethernet (PoE) 6 port Gigabit switch offered by Tycon® is a fully automatic high speed Layer 2+ Ethernet manageable switches. The 6 port model has 4 PoE + 2 SFP ports. The PoE ports are Mode A (pins 1,2,3,6) type and are manageable via the user interface. They can be set to PoE, PoE+ or OFF. Default is PoE+.

The switch features security protocols like SSH and SSL for secure access of the switch command interface. The interface can be accessed via the serial console port or any of the Ethernet ports. The command interface can be controlled via web browser, command line interface(CLI), TELNET, SSH or SNMP.

DATA SHEET

Brands: Ubiquiti

USP-RPS

The UniFi SmartPower Redundant Power System, model USP-RPS, is a proprietary redundant power system designed to protect up to six UniFi SmartPower supported devices from sudden power supply module failure.

The USP-RPS continually monitors all attached devices. In the event of an internal AC/DC power supply failure, failover is automatic so your network continues to operate with no interruption in service. With a 950W DC power budget, the USP-RPS can protect a variety of high-power devices, including UniFi PoE switches. An integrated 1.3" color touchscreen LCM displays system information for convenient monitoring.

DATA SHEET

Brands: Tycon Systems

TP-DCDC-1224 9-36VDC IN 24V PoE OUT 24W DC to DC Converter and PoE inserter DATA SHEET

TP-DCDC-1224G Gigabit 9-36VDC IN 24V PoE OUT 20W DC to DC Converter and PoE inserter DATA SHEET

TP-DCDC-1224G-4P Gigabit 9-36VDC IN 24VDC 4 Pair PoE OUT 24W DC to DC Converter and PoE inserter

Brands: Tycon Systems

TPDIN-MONITOR-WEB2

The TPDIN® Based Remote Monitor and Control System is a versatile tool which enables the equipment designer and installer to remotely monitor their equipment and site. The unit can be accessed via the network (web and SNMP) to remotely monitor up to 4 voltages, 4 currents, 2 temperatures and control power to various equipment using 4 on-board relays. The system has built-in surge protection to prevent damage from electrical surges.

DATA SHEET

Brands: Tycon Systems

PSDIN-48-240W

The PSDIN Series of Industrial DIN Rail mount high efficiency switching power supplies operate over a wide temperature range of -40C to +70C. There are two models to supply 120W or 240W. The input is 90 to 264VAC auto-ranging with wire terminal connections. The output is 48VDC nominal with an adjustment range from 47VDC to 56VDC. There is a switch for single or parallel operation. Two 240W supplies operating in parallel will provide 480W total power. There is an alarm output to provide a dry contact closure to trigger an alarm if the DC output fails, like during a grid power failure. The relay is closed when DC output is normal and open when DC output is in fault condition due to overload or safety shutdown.

DATA SHEET

Brands: Tycon Systems

TP-SW5GD-BT

The TP-SW5GD-BT Power over Ethernet (PoE) 5 Port Gigabit switch offered by Tycon® is a fully automatic high speed Layer 2 Ethernet switch with one 802.3bt PoE input and four 802.3at PoE outputs. Ports 1-4 are 802.3at 35W PoE Out. The Uplink Port 5, is 802.3bt compatible so the switch can accept up to 100W PoE on 4 pairs to power the switch and connected devices remotely over CAT5 or higher Ethernet Cable. The Ethernet spec supports distances up to 100m (328ft). By using as a repeater, 200m total distance is realistic.

The switch can accept power via three different interfaces: Wire Terminal Connector, 4 pin Mini DIN connector or via 802.3at/bt PoE input to Uplink Port 5. Two different power inputs can be used for redundancy. The higher voltage takes priority.

DATA SHEET

Brands: Tycon Systems

TP-DCDC-2USB-24

USB Powered 24V Passive PoE inserter. 24VDC 12W Passive PoE Output with 2 USB power inputs. 10/100Mb.

The TP-DCDC-2USB-24 Passive Power Over Ethernet Power Source offered by Tycon Power Systems is a unique 24VDC Passive POE injector powered by two USB ports. They work by supplying power to the remote device on the 4 unused Ethernet pins 4,5(+) and 7,8(-). The Ethernet spec supports distances up to 100m (328 feet).

DATA SHEET

Brands: Ubiquiti

F-POE-G2

Optical Data Transport for Outdoor POE Devices

The FiberPoE connects remote PoE devices and provides data and power using fiber and DC cabling.

DATA SHEET

Brands: Tycon Systems

TP-SSW5-NC

Universal Voltage 10/100 PoE Switch. Switch accepts universal voltage (12-57VDC) via the wire terminal connector on the back of the Switch. This model is very compact at only 4”x5”x1.5”. 2A per port.

On the universal voltage models (“-NC”) the PoE output voltage = the input voltage so it is universal in its application. The Ethernet spec supports distances up to 100m (328 feet) between the PoE switch and the remote device.

Tycon Power® sells a variety of power supplies in 60W, 120W and 180W sizes. 18VDC, 24VDC and 48VDC are available. All the Switches have DIN Rail mounts included for convenient DIN rail mounting.

DATA SHEET

Brands: Tycon Systems

TP-DCDC-4848GD

The TP-DCDC-4848GD Gigabit Series of DC to DC converters have an integrated Gigabit POE injector to apply the power and data output to the CAT5 Ethernet cable. The output voltage is regulated and protected. They have two isolated inputs for connecting 2 power sources, like a primary and backup power source. A metal enclosure model is available for industrial applications. They accept gigabit data-in to a shielded RJ45 Jack and provide gigabit data-out and PoE power on the shielded RJ45 output jack. They work by supplying power on the unused Ethernet pins 4,5(V+) and 7,8(V-). They have various protections for surge, short circuit and overload. The units have power outputs up to 17W.

DATA SHEET

Brands: Tycon Systems

TP-VRHP-2456-250

Voltage Converter 18-36VDC Input, 56VDC @ 4.46A 250W Regulated output. 

The TP-VRHP-2456-250 is a high power 250W voltage converter/regulator which accepts an input of plus or minus 18VDC to 36VDC and provides a regulated output of 56VDC @ 4.46A 250W. These units are perfect for providing 56VDC voltage from 24VDC battery banks. Input and outputs are wire terminals for wire up to 12AWG. Operates from -30 to +65 deg C.

DATA SHEET