12-56V 5 Port Multi-Volt Gigabit Passive PoE Switch

12-56V 5 Port Multi-Volt Gigabit Passive PoE Switch

TP-SW5G-MULTI

Universal Multiple Voltage (MultiVolt™) 10/100/1000MB PoE Switch. Switch accepts up to 4 different voltages (12-57VDC) so user can power both 48V PoE and 24V PoE devices from the same switch. The port can individually be set to Data Only by disconnecting the voltage input to that specific port. 1A per port.

On the universal voltage models (“-NC”) the PoE output voltage = the input voltage so it is universal in its application. The Ethernet spec supports distances up to 100m (328 feet) between the PoE switch and the remote device.

Tycon Power® sells a variety of power supplies in 60W, 120W and 180W sizes. 18VDC, 24VDC and 48VDC are available. All the Switches have DIN Rail mounts included for convenient DIN rail mounting.

DATA SHEET

TP-SW5G-MULTI

Write your review

12-56V 5 Port Multi-Volt Gigabit Passive PoE Switch

TP-SW5G-MULTI

Universal Multiple Voltage (MultiVolt™) 10/100/1000MB PoE Switch. Switch accepts up to 4 different voltages (12-57VDC) so user can power both 48V PoE and 24V PoE devices from the same switch. The port can individually be set to Data Only by disconnecting the voltage input to that specific port. 1A per port.

On the universal voltage models (“-NC”) the PoE output voltage = the input voltage so it is universal in its application. The Ethernet spec supports distances up to 100m (328 feet) between the PoE switch and the remote device.

Tycon Power® sells a variety of power supplies in 60W, 120W and 180W sizes. 18VDC, 24VDC and 48VDC are available. All the Switches have DIN Rail mounts included for convenient DIN rail mounting.

DATA SHEET

Write your review

16 other products in the same category

Brands: Tycon Systems

TP-DCDC-4824G

The TP-DCDC Gigabit Series of DC to DC converters offered by Tycon Power® are a low cost and high efficiency solution for those requiring IEEE802.3af or Passive Power over Ethernet from a 12VDC or 24VDC or 48VDC voltage source like a battery system or vehicle. They have an integrated POE injector to apply the power and data output to the CAT5 Ethernet cable. The output voltage is regulated and protected. They have two isolated inputs for connecting 2 power sources, like a primary and backup power source. A metal enclosure model is available for industrial applications.

DATA SHEET

Brands: Tycon Systems

TP-SW5GD-BT

The TP-SW5GD-BT Power over Ethernet (PoE) 5 Port Gigabit switch offered by Tycon® is a fully automatic high speed Layer 2 Ethernet switch with one 802.3bt PoE input and four 802.3at PoE outputs. Ports 1-4 are 802.3at 35W PoE Out. The Uplink Port 5, is 802.3bt compatible so the switch can accept up to 100W PoE on 4 pairs to power the switch and connected devices remotely over CAT5 or higher Ethernet Cable. The Ethernet spec supports distances up to 100m (328ft). By using as a repeater, 200m total distance is realistic.

The switch can accept power via three different interfaces: Wire Terminal Connector, 4 pin Mini DIN connector or via 802.3at/bt PoE input to Uplink Port 5. Two different power inputs can be used for redundancy. The higher voltage takes priority.

DATA SHEET

Brands: Tycon Systems

TP-DCDC-2USB-24

USB Powered 24V Passive PoE inserter. 24VDC 12W Passive PoE Output with 2 USB power inputs. 10/100Mb.

The TP-DCDC-2USB-24 Passive Power Over Ethernet Power Source offered by Tycon Power Systems is a unique 24VDC Passive POE injector powered by two USB ports. They work by supplying power to the remote device on the 4 unused Ethernet pins 4,5(+) and 7,8(-). The Ethernet spec supports distances up to 100m (328 feet).

DATA SHEET

Brands: Tycon Systems

TP-SW8G-2SFP

The TP-SW8G-2SFP Power over Ethernet (PoE) 10 port Gigabit switch offered by Tycon® is a fully automatic high speed Layer 2+ Ethernet manageable switches. The 10 port model has 8 PoE + 2 SFP ports. The PoE ports are Mode A (pins 1,2,3,6) type and are manageable via the user interface. They can be set to PoE, PoE+ or OFF. Default is PoE+.

The switch features security protocols like SSH and SSL for secure access of the switch command interface. The interface can be accessed via the serial console port or any of the Ethernet ports. The command interface can be controlled via web browser, command line interface(CLI), TELNET, SSH or SNMP.

DATA SHEET

Brands: Tycon Systems

TP-DCDC-4848GD

The TP-DCDC-4848GD Gigabit Series of DC to DC converters have an integrated Gigabit POE injector to apply the power and data output to the CAT5 Ethernet cable. The output voltage is regulated and protected. They have two isolated inputs for connecting 2 power sources, like a primary and backup power source. A metal enclosure model is available for industrial applications. They accept gigabit data-in to a shielded RJ45 Jack and provide gigabit data-out and PoE power on the shielded RJ45 output jack. They work by supplying power on the unused Ethernet pins 4,5(V+) and 7,8(V-). They have various protections for surge, short circuit and overload. The units have power outputs up to 17W.

DATA SHEET

Brands: Tycon Systems

TP-POE-1824

48V 802.3af/at input, Switch Selectable 18V or 24V 12W passive PoE output. 10/100Mb. Converts 802.3af PoE to passive PoE.

802.3af/at Converter - Converts 48V 802.3af/at PoE to 18/24VDC (switchable) Passive PoE

The TP-POE-1824 Power Over Ethernet 802.3af/at converter is a unique product allowing a customer to run a Passive PoE device from a standard 802.3af or at PoE switch. They accept 802.3af/at PoE in and provide a switch selectable 12W PoE output of 18VDC or 24VDC.

DATA SHEET

Brands: Tycon Systems

TP-SW5G-NC

Universal Voltage 10/100/1000MB PoE Switch. Switch accepts universal voltage (12- 57VDC) via the wire terminal connector on the back of the switch. Also accepts 12-57VDC (1A max) Passive PoE input on port 5. 1A per port

On the universal voltage models (“-NC”) the PoE output voltage = the input voltage so it is universal in its application. The Ethernet spec supports distances up to 100m (328 feet) between the PoE switch and the remote device.

Tycon Power® sells a variety of power supplies in 60W, 120W and 180W sizes. 18VDC, 24VDC and 48VDC are available. All the Switches have DIN Rail mounts included for convenient DIN rail mounting.

DATA SHEET

Brands: Tycon Systems

TP-DCDC-1224 9-36VDC IN 24V PoE OUT 24W DC to DC Converter and PoE inserter DATA SHEET

TP-DCDC-1224G Gigabit 9-36VDC IN 24V PoE OUT 20W DC to DC Converter and PoE inserter DATA SHEET

TP-DCDC-1224G-4P Gigabit 9-36VDC IN 24VDC 4 Pair PoE OUT 24W DC to DC Converter and PoE inserter

Brands: Tycon Systems

TP-DCDC-1256G-VHP Gigabit 10-60VDC IN 56VDC OUT 70W 4 Pair Hi Power DC to DC Converter and passive PoE inserter. Ubiquiti airFiber™ DATA SHEET

TP-DCDC-1256GD-VHP Gigabit 10-60VDC IN 56VDC OUT 70W 4 Pair Hi Power DC to DC Conv and 802.3at PoE inserter. For Axis Q60 series PTZ cameras. UPOE Compatible. DATA SHEET

TP-DCDC-1256GD-BT Gigabit 10-60VDC IN 56VDC OUT 70W 4 Pair Hi Power DC to DC Conv and 802.3bt PoE inserter. DATA SHEET

Brands: Tycon Systems

TP-SW5G-24

The SW5 Series Power over Ethernet (PoE) switches offered by Tycon Power® are fully automatic high speed 5 port Ethernet switches with up to 2A of PoE power per port.

IEEE802.3af/at Compliant 48VDC 10/100/1000MB PoE Switch. Switch accepts 12-36VDC power via a wire terminal connector on the back of the Switch or via 48VDC PoE into the 802.3af/at compliant uplink port (90W max). Perfect for remote solar/battery systems. 35W per port. 70W Max Total.

On the universal voltage models (“-NC”) the PoE output voltage = the input voltage so it is universal in its application. The Ethernet spec supports distances up to 100m (328 feet) between the PoE switch and the remote device.

DATA SHEET

Brands: Tycon Systems

TP-DCDC-1218

9-36VDC IN, 18V 18W Passive PoE OUT, DC to DC Converter/PoE inserter. 10/100Mb.

The TP-DCDC-1218 DC to DC converters offered by Tycon Power Systems are a low cost and high reliability solution for those requiring 18VDC Power Over Ethernet voltage from a 12 or 24V battery system. 

They have an integrated PoE injector to apply the regulated 18VDC to the CAT5 Ethernet cable. The input voltage must be between 9VDC and 36VDC.

DATA SHEET