24VDC to 56VDC 70W DCDC Voltage Converter

24VDC to 56VDC 70W DCDC Voltage Converter

TP-VRHP-2456

Voltage Converter 18-36VDC Input, 56VDC @ 1.5A 70W Regulated output. 

The TP-VRHP-2456 is a 70W voltage converter/regulator which accepts an input of plus or minus +/-18VDC to 36VDC and provides a regulated output of 56VDC @ 1.25A 70W. These units are perfect for providing 56VDC voltage from -24VDC telecom power. Input and outputs are wire terminals for wire up to 12AWG. Operates from -30 to +65 deg C (-22 deg F to 149 deg F). 

DATA SHEET

TP-VRHP-2456

Write your review

24VDC to 56VDC 70W DCDC Voltage Converter

TP-VRHP-2456

Voltage Converter 18-36VDC Input, 56VDC @ 1.5A 70W Regulated output. 

The TP-VRHP-2456 is a 70W voltage converter/regulator which accepts an input of plus or minus +/-18VDC to 36VDC and provides a regulated output of 56VDC @ 1.25A 70W. These units are perfect for providing 56VDC voltage from -24VDC telecom power. Input and outputs are wire terminals for wire up to 12AWG. Operates from -30 to +65 deg C (-22 deg F to 149 deg F). 

DATA SHEET

Write your review

16 other products in the same category

Brands: Tycon Systems

TP-DCDC-2424GR-VHP

The Gigabit compatible TP-DCDC-2424GR-VHP are special very high power DC to DC converters / PoE inserters designed especially for Ubiquiti airFiber x™ wireless radio systems and other systems which require high power passive PoE (High PoE). The unique PoE inserter supplies 24VDC PoE power on all 8 Ethernet wires (4 pair) with the following pinout: 1,2,4,5 V+ and 3,6,7,8 V

They have two isolated inputs for connecting 2 power sources, like a primary and backup power source. They have various protections for surge, short circuit and overload. The input and output are isolated.

DATA SHEET

Brands: Ubiquiti

F-POE-G2

Optical Data Transport for Outdoor POE Devices

The FiberPoE connects remote PoE devices and provides data and power using fiber and DC cabling.

DATA SHEET

Brands: Tycon Systems

TP-SW8G-2SFP

The TP-SW8G-2SFP Power over Ethernet (PoE) 10 port Gigabit switch offered by Tycon® is a fully automatic high speed Layer 2+ Ethernet manageable switches. The 10 port model has 8 PoE + 2 SFP ports. The PoE ports are Mode A (pins 1,2,3,6) type and are manageable via the user interface. They can be set to PoE, PoE+ or OFF. Default is PoE+.

The switch features security protocols like SSH and SSL for secure access of the switch command interface. The interface can be accessed via the serial console port or any of the Ethernet ports. The command interface can be controlled via web browser, command line interface(CLI), TELNET, SSH or SNMP.

DATA SHEET

Brands: Tycon Systems

TP-POE-1824G

48V 802.3af/at Gigabit input, Switch Selectable 18V or 24V 24W Gigabit passive PoE output. Converts 802.3af/at PoE to passive PoE.

The TP-POE-1824G Power Over Ethernet 802.3af/at converter is a unique product allowing a customer to run a Passive PoE device from a standard 802.3af or at PoE switch. They accept 802.3af/at PoE in and provide a switch selectable 24W PoE output of 18VDC or 24VDC.

DATA SHEET

Brands: Tycon Systems

TP-DCDC-1224-HP

The TP-DCDC-HP Series of DC to DC converters offered by Tycon Power® are a low cost and high reliability solution for those requiring 24VDC or 56VDC Power over Ethernet voltage from a 12V, 24V or 48V battery system. They have an integrated PoE injector. Passive PoE and 802.3at models are available.

The input and output are isolated so the units can accept minus voltage on input and can be wired for positive voltage on the output for those systems which are negative voltage based.

If the remote device does not support power over Ethernet, splitters (POE-SPLT-S) are available to split the data and DC voltage at the remote device. If the remote device requires reverse voltage the POE-XOVER-S cable can be used.

DATA SHEET

Brands: Tycon Systems

PSDIN-48-240W

The PSDIN Series of Industrial DIN Rail mount high efficiency switching power supplies operate over a wide temperature range of -40C to +70C. There are two models to supply 120W or 240W. The input is 90 to 264VAC auto-ranging with wire terminal connections. The output is 48VDC nominal with an adjustment range from 47VDC to 56VDC. There is a switch for single or parallel operation. Two 240W supplies operating in parallel will provide 480W total power. There is an alarm output to provide a dry contact closure to trigger an alarm if the DC output fails, like during a grid power failure. The relay is closed when DC output is normal and open when DC output is in fault condition due to overload or safety shutdown.

DATA SHEET

Brands: Ubiquiti

USP-RPS

The UniFi SmartPower Redundant Power System, model USP-RPS, is a proprietary redundant power system designed to protect up to six UniFi SmartPower supported devices from sudden power supply module failure.

The USP-RPS continually monitors all attached devices. In the event of an internal AC/DC power supply failure, failover is automatic so your network continues to operate with no interruption in service. With a 950W DC power budget, the USP-RPS can protect a variety of high-power devices, including UniFi PoE switches. An integrated 1.3" color touchscreen LCM displays system information for convenient monitoring.

DATA SHEET

Brands: Tycon Systems

TP-DCDC-4848GD

The TP-DCDC-4848GD Gigabit Series of DC to DC converters have an integrated Gigabit POE injector to apply the power and data output to the CAT5 Ethernet cable. The output voltage is regulated and protected. They have two isolated inputs for connecting 2 power sources, like a primary and backup power source. A metal enclosure model is available for industrial applications. They accept gigabit data-in to a shielded RJ45 Jack and provide gigabit data-out and PoE power on the shielded RJ45 output jack. They work by supplying power on the unused Ethernet pins 4,5(V+) and 7,8(V-). They have various protections for surge, short circuit and overload. The units have power outputs up to 17W.

DATA SHEET

Brands: Mikrotik

MTP250-26V94-OD

Outdoor IP67 26V 250W AC/DC power supply units for the MikroTik NetPower 16P. Built for situations when your outdoor switches need that extra juice. Pole/wall mount compatible!

DATA SHEET

Brands: Tycon Systems

TP-DCDC-4856G-VHP

The Gigabit compatible TP-DCDC-2456G-VHP and TP-DCDC4856G-VHP area special very high power DC to DC converters / PoE inserters designed especially for Ubiquiti airFiber™ antenna systems and other systems which require high power passive PoE such as Axis High Power PoE PTZ security cameras. The unique PoE inserter supplies 56VDC PoE power on all 8 Ethernet wires.

They have two isolated inputs for connecting 2 power sources, like a primary and backup power source. They have various protections for surge, short circuit and overload. The input and output are isolated.

DATA SHEET

Brands: Tycon Systems

TP-SW3G

The TP-SW3G Power over Ethernet (PoE) 3 Port Gigabit switches offered by Tycon® are fully automatic high speed Ethernet switches with up to 30W of PoE power per port.

The unit accepts Gigabit data and power via PoE into the RJ45 “PoE In” port. The PoE In port is compatible with IEEE802.3af, IEEE802.3at and IEEE802.3at 4 pair (60W). It can also accept 42-57VDC Passive PoE.

There are two fully compliant 802.3af/at Gigabit “PoE Out” ports. These ports are capable of up to 30W per port and 100m (330ft) distance.

DATA SHEET