BreezePro® 400W 12V/24V Horizontal Wind Turbine

BreezePro® 400W 12V/24V Horizontal Wind Turbine

TPW-400DT-12/24

The BreezePro® Wind Turbines from Tycon Solar® are lightweight at less than 10.5kg and are designed for ease of installation and long service life. The generator is a very low cogging force design for better performance in light winds and is packaged in a fully sealed die cast aluminum enclosure. There are no brushes to wear out or cause electrical noise and the bearings are sealed so the system is maintenance free. The blades are glass reinforced nylon for high strength, UV resistance and fatigue resistance. The turbines are 12V/24V auto voltage select.

DATA SHEET

TPW-400DT-12/24

Write your review

BreezePro® 400W 12V/24V Horizontal Wind Turbine

TPW-400DT-12/24

The BreezePro® Wind Turbines from Tycon Solar® are lightweight at less than 10.5kg and are designed for ease of installation and long service life. The generator is a very low cogging force design for better performance in light winds and is packaged in a fully sealed die cast aluminum enclosure. There are no brushes to wear out or cause electrical noise and the bearings are sealed so the system is maintenance free. The blades are glass reinforced nylon for high strength, UV resistance and fatigue resistance. The turbines are 12V/24V auto voltage select.

DATA SHEET

Write your review

16 other products in the same category

Brands: Tycon Systems

TP-VRHP-2456-250

Voltage Converter 18-36VDC Input, 56VDC @ 4.46A 250W Regulated output. 

The TP-VRHP-2456-250 is a high power 250W voltage converter/regulator which accepts an input of plus or minus 18VDC to 36VDC and provides a regulated output of 56VDC @ 4.46A 250W. These units are perfect for providing 56VDC voltage from 24VDC battery banks. Input and outputs are wire terminals for wire up to 12AWG. Operates from -30 to +65 deg C.

DATA SHEET

Brands: Tycon Systems

TP-SW5G-MULTI

Universal Multiple Voltage (MultiVolt™) 10/100/1000MB PoE Switch. Switch accepts up to 4 different voltages (12-57VDC) so user can power both 48V PoE and 24V PoE devices from the same switch. The port can individually be set to Data Only by disconnecting the voltage input to that specific port. 1A per port.

On the universal voltage models (“-NC”) the PoE output voltage = the input voltage so it is universal in its application. The Ethernet spec supports distances up to 100m (328 feet) between the PoE switch and the remote device.

Tycon Power® sells a variety of power supplies in 60W, 120W and 180W sizes. 18VDC, 24VDC and 48VDC are available. All the Switches have DIN Rail mounts included for convenient DIN rail mounting.

DATA SHEET

Brands: Tycon Systems

TPDIN-MONITOR-WEB2

The TPDIN® Based Remote Monitor and Control System is a versatile tool which enables the equipment designer and installer to remotely monitor their equipment and site. The unit can be accessed via the network (web and SNMP) to remotely monitor up to 4 voltages, 4 currents, 2 temperatures and control power to various equipment using 4 on-board relays. The system has built-in surge protection to prevent damage from electrical surges.

DATA SHEET

Brands: Tycon Systems

TP-DCDC-4848GD

The TP-DCDC-4848GD Gigabit Series of DC to DC converters have an integrated Gigabit POE injector to apply the power and data output to the CAT5 Ethernet cable. The output voltage is regulated and protected. They have two isolated inputs for connecting 2 power sources, like a primary and backup power source. A metal enclosure model is available for industrial applications. They accept gigabit data-in to a shielded RJ45 Jack and provide gigabit data-out and PoE power on the shielded RJ45 output jack. They work by supplying power on the unused Ethernet pins 4,5(V+) and 7,8(V-). They have various protections for surge, short circuit and overload. The units have power outputs up to 17W.

DATA SHEET

Brands: Mikrotik

RBGPOE

PoE injector, for Gigabit LAN products

The new MikroTik Gigabit PoE adapter for powering any RouterBOARD over Gigabit Ethernet. Simply connect your power source and then use an ethernet cable to connect the injector to the RouterBOARD device.

For using with any RouterBOARD that supports 9-48V PoE. 

The GPOE has shielded connectors.

DATA SHEET

Brands: Ubiquiti

F-POE-G2

Optical Data Transport for Outdoor POE Devices

The FiberPoE connects remote PoE devices and provides data and power using fiber and DC cabling.

DATA SHEET

Brands: Tycon Systems

TP-MS4G-VHP

Gigabit Mid Span, Very High Power 1.8A per port, UniVolt™ PoE Injector.

The TP-MS4G-VHP mid span PoE power sources are used for supplying PoE and data to multiple devices from a central location such as an operations room or equipment cabinet. The PoE devices feature a separate data-in port coupled with a data out/PoE port. The PoE function is considered 4 Pair Passive PoE which is sometimes referred to as “High PoE”. The units support Gigabit Ethernet and are backward compatible to 10/100MB.

DATA SHEET

Brands: Tycon Systems

TP-SW8-NC

The TP-SW8-D Power over Ethernet 802.3af/at (PoE) 10/100Mb switch offered by Tycon Power® is a fully automatic high speed 8 port Ethernet switch.

The -NC version is a passive PoE model for devices which are not 802.3af/at compliant.

On the -NC version the PoE output voltage = the input voltage so it is universal in its application. The DC input power range can be from 12V to 57V. The units can be powered via 2 or 4 pair PoE to port 8 (2A max).

DATA SHEET

Brands: Tycon Systems

TP-VRHP-2424

Voltage Converter 18-36VDC Input, 24VDC @ 2.9A 70W Regulated output. 

he TP-VRHP-2424 is a 70W voltage converter/regulator which accepts an input of plus or minus 18VDC to 36VDC and provides a regulated output of 24VDC @ 2.9A 70W. These units are perfect for providing stable regulated 24VDC voltage from 24VDC battery banks. Input and outputs are wire terminals for wire up to 12AWG. Operates from -30 to +65 deg C.

DATA SHEET

Brands: Tycon Systems

TP-SW5G-D

The SW5 Series Power over Ethernet (PoE) switches offered by Tycon Power® are fully automatic high speed 5 port Ethernet switches with up to 2A of PoE power per port.

IEEE802.3af/at Compliant 48VDC 10/100/1000MB PoE Switch. Switch accepts 48VDC power via a wire terminal connector on the back of the Switch or via 48VDC PoE into the 802.3af/at compliant uplink port (90W max). 35W per port.

On the universal voltage models (“-NC”) the PoE output voltage = the input voltage so it is universal in its application. The Ethernet spec supports distances up to 100m (328 feet) between the PoE switch and the remote device.

DATA SHEET

Brands: Tycon Systems

TP-VRHP-2456

Voltage Converter 18-36VDC Input, 56VDC @ 1.5A 70W Regulated output. 

The TP-VRHP-2456 is a 70W voltage converter/regulator which accepts an input of plus or minus +/-18VDC to 36VDC and provides a regulated output of 56VDC @ 1.25A 70W. These units are perfect for providing 56VDC voltage from -24VDC telecom power. Input and outputs are wire terminals for wire up to 12AWG. Operates from -30 to +65 deg C (-22 deg F to 149 deg F). 

DATA SHEET