Power Supply, 100W DC

Power Supply, 100W DC

RPS-DC-100W

RPS DC/DC Power Supply
Supported Voltage Range: 38 to 54VDC, 24VDC Output

DATA SHEET

RPS-DC-100W

Write your review

Power Supply, 100W DC

RPS-DC-100W

RPS DC/DC Power Supply
Supported Voltage Range: 38 to 54VDC, 24VDC Output

DATA SHEET

Write your review

16 other products in the same category

Brands: Tycon Systems

TP-SW8G-2SFP

The TP-SW8G-2SFP Power over Ethernet (PoE) 10 port Gigabit switch offered by Tycon® is a fully automatic high speed Layer 2+ Ethernet manageable switches. The 10 port model has 8 PoE + 2 SFP ports. The PoE ports are Mode A (pins 1,2,3,6) type and are manageable via the user interface. They can be set to PoE, PoE+ or OFF. Default is PoE+.

The switch features security protocols like SSH and SSL for secure access of the switch command interface. The interface can be accessed via the serial console port or any of the Ethernet ports. The command interface can be controlled via web browser, command line interface(CLI), TELNET, SSH or SNMP.

DATA SHEET

Brands: Tycon Systems

TP-DCDC-1218

9-36VDC IN, 18V 18W Passive PoE OUT, DC to DC Converter/PoE inserter. 10/100Mb.

The TP-DCDC-1218 DC to DC converters offered by Tycon Power Systems are a low cost and high reliability solution for those requiring 18VDC Power Over Ethernet voltage from a 12 or 24V battery system. 

They have an integrated PoE injector to apply the regulated 18VDC to the CAT5 Ethernet cable. The input voltage must be between 9VDC and 36VDC.

DATA SHEET

Brands: Tycon Systems

TP-DCDC-4848GD

The TP-DCDC-4848GD Gigabit Series of DC to DC converters have an integrated Gigabit POE injector to apply the power and data output to the CAT5 Ethernet cable. The output voltage is regulated and protected. They have two isolated inputs for connecting 2 power sources, like a primary and backup power source. A metal enclosure model is available for industrial applications. They accept gigabit data-in to a shielded RJ45 Jack and provide gigabit data-out and PoE power on the shielded RJ45 output jack. They work by supplying power on the unused Ethernet pins 4,5(V+) and 7,8(V-). They have various protections for surge, short circuit and overload. The units have power outputs up to 17W.

DATA SHEET

Brands: Tycon Systems

POE-PowerTap

Taps into passive PoE power on RJ45 connectors and outputs to a wire terminal connection. Pins 4,5 and 7,8. Can also be used to inject power.

Tycon Power Systems

The POE-PowerTap is a unique tool that allows monitoring or testing of PoE voltages, Extracting PoE voltage from a PoE switch or injector or Injecting PoE voltages to a CAT5 cable. The POE-PowerTap is outfitted with a wire terminal connector for up to 12awg wire.

DATA SHEET

Brands: Tycon Systems

PSDIN-48-240W

The PSDIN Series of Industrial DIN Rail mount high efficiency switching power supplies operate over a wide temperature range of -40C to +70C. There are two models to supply 120W or 240W. The input is 90 to 264VAC auto-ranging with wire terminal connections. The output is 48VDC nominal with an adjustment range from 47VDC to 56VDC. There is a switch for single or parallel operation. Two 240W supplies operating in parallel will provide 480W total power. There is an alarm output to provide a dry contact closure to trigger an alarm if the DC output fails, like during a grid power failure. The relay is closed when DC output is normal and open when DC output is in fault condition due to overload or safety shutdown.

DATA SHEET

Brands: Tycon Systems

TPDIN-MONITOR-WEB2

The TPDIN® Based Remote Monitor and Control System is a versatile tool which enables the equipment designer and installer to remotely monitor their equipment and site. The unit can be accessed via the network (web and SNMP) to remotely monitor up to 4 voltages, 4 currents, 2 temperatures and control power to various equipment using 4 on-board relays. The system has built-in surge protection to prevent damage from electrical surges.

DATA SHEET

Brands: Tycon Systems

TP-SW3G

The TP-SW3G Power over Ethernet (PoE) 3 Port Gigabit switches offered by Tycon® are fully automatic high speed Ethernet switches with up to 30W of PoE power per port.

The unit accepts Gigabit data and power via PoE into the RJ45 “PoE In” port. The PoE In port is compatible with IEEE802.3af, IEEE802.3at and IEEE802.3at 4 pair (60W). It can also accept 42-57VDC Passive PoE.

There are two fully compliant 802.3af/at Gigabit “PoE Out” ports. These ports are capable of up to 30W per port and 100m (330ft) distance.

DATA SHEET

Brands: Tycon Systems

TP-VRHP-4856

Voltage Converter 18-36VDC Input, 56VDC @ 1.5A 70W Regulated output. 

The TP-VRHP-4856 is a 70W voltage converter/regulator which accepts an input of plus or minus +/-18VDC to 36VDC and provides a regulated output of 56VDC @ 1.25A 70W. These units are perfect for providing 56VDC voltage from -48VDC telecom power. Input and outputs are wire terminals for wire up to 12AWG. Operates from -30 to +65 deg C (-22 deg F to 149 deg F). 

DATA SHEET

Brands: Tycon Systems

TP-POE-1824G

48V 802.3af/at Gigabit input, Switch Selectable 18V or 24V 24W Gigabit passive PoE output. Converts 802.3af/at PoE to passive PoE.

The TP-POE-1824G Power Over Ethernet 802.3af/at converter is a unique product allowing a customer to run a Passive PoE device from a standard 802.3af or at PoE switch. They accept 802.3af/at PoE in and provide a switch selectable 24W PoE output of 18VDC or 24VDC.

DATA SHEET

Brands: Mikrotik

RBGPOE

PoE injector, for Gigabit LAN products

The new MikroTik Gigabit PoE adapter for powering any RouterBOARD over Gigabit Ethernet. Simply connect your power source and then use an ethernet cable to connect the injector to the RouterBOARD device.

For using with any RouterBOARD that supports 9-48V PoE. 

The GPOE has shielded connectors.

DATA SHEET

Brands: Tycon Systems

TP-VRHP-2424

Voltage Converter 18-36VDC Input, 24VDC @ 2.9A 70W Regulated output. 

he TP-VRHP-2424 is a 70W voltage converter/regulator which accepts an input of plus or minus 18VDC to 36VDC and provides a regulated output of 24VDC @ 2.9A 70W. These units are perfect for providing stable regulated 24VDC voltage from 24VDC battery banks. Input and outputs are wire terminals for wire up to 12AWG. Operates from -30 to +65 deg C.

DATA SHEET