Passive PoE Power Tap Adapter

PSDIN-48-240W

The PSDIN Series of Industrial DIN Rail mount high efficiency switching power supplies operate over a wide temperature range of -40C to +70C. There are two models to supply 120W or 240W. The input is 90 to 264VAC auto-ranging with wire terminal connections. The output is 48VDC nominal with an adjustment range from 47VDC to 56VDC. There is a switch for single or parallel operation. Two 240W supplies operating in parallel will provide 480W total power. There is an alarm output to provide a dry contact closure to trigger an alarm if the DC output fails, like during a grid power failure. The relay is closed when DC output is normal and open when DC output is in fault condition due to overload or safety shutdown.

DATA SHEET

TP-SW3G

The TP-SW3G Power over Ethernet (PoE) 3 Port Gigabit switches offered by Tycon® are fully automatic high speed Ethernet switches with up to 30W of PoE power per port.

The unit accepts Gigabit data and power via PoE into the RJ45 “PoE In” port. The PoE In port is compatible with IEEE802.3af, IEEE802.3at and IEEE802.3at 4 pair (60W). It can also accept 42-57VDC Passive PoE.

There are two fully compliant 802.3af/at Gigabit “PoE Out” ports. These ports are capable of up to 30W per port and 100m (330ft) distance.

DATA SHEET

RBGPOE

PoE injector, for Gigabit LAN products

The new MikroTik Gigabit PoE adapter for powering any RouterBOARD over Gigabit Ethernet. Simply connect your power source and then use an ethernet cable to connect the injector to the RouterBOARD device.

For using with any RouterBOARD that supports 9-48V PoE. 

The GPOE has shielded connectors.

DATA SHEET

TP-DCDC-1224-HP

The TP-DCDC-HP Series of DC to DC converters offered by Tycon Power® are a low cost and high reliability solution for those requiring 24VDC or 56VDC Power over Ethernet voltage from a 12V, 24V or 48V battery system. They have an integrated PoE injector. Passive PoE and 802.3at models are available.

The input and output are isolated so the units can accept minus voltage on input and can be wired for positive voltage on the output for those systems which are negative voltage based.

If the remote device does not support power over Ethernet, splitters (POE-SPLT-S) are available to split the data and DC voltage at the remote device. If the remote device requires reverse voltage the POE-XOVER-S cable can be used.

DATA SHEET

TP-VRHP-1256

Voltage Converter 10-15VDC Input, 56VDC @ 1.25A 70W Regulated output. 

The TP-VRHP-1256 is a 70W voltage converter/regulator which accepts an input of plus or minus 10VDC to 15VDC and provides a regulated output of 56VDC @ 1.25A 70W. These units are perfect for providing 56VDC voltage from 12VDC battery source like in a vehicular application or remote power application. Input and outputs are wire terminals for wire up to 12AWG. Operates from -30 to +65 deg C. 

DATA SHEET

MTP250-53V47-OD

Outdoor 53V 250W AC/DC power supply units for the MikroTik NetPower 16P. Built for situations when your outdoor switches need that extra juice. Pole/wall mount compatible!

DATA SHEET

TP-VRHP-4856

Voltage Converter 18-36VDC Input, 56VDC @ 1.5A 70W Regulated output. 

The TP-VRHP-4856 is a 70W voltage converter/regulator which accepts an input of plus or minus +/-18VDC to 36VDC and provides a regulated output of 56VDC @ 1.25A 70W. These units are perfect for providing 56VDC voltage from -48VDC telecom power. Input and outputs are wire terminals for wire up to 12AWG. Operates from -30 to +65 deg C (-22 deg F to 149 deg F). 

DATA SHEET

TPDIN-MONITOR-WEB2

The TPDIN® Based Remote Monitor and Control System is a versatile tool which enables the equipment designer and installer to remotely monitor their equipment and site. The unit can be accessed via the network (web and SNMP) to remotely monitor up to 4 voltages, 4 currents, 2 temperatures and control power to various equipment using 4 on-board relays. The system has built-in surge protection to prevent damage from electrical surges.

DATA SHEET

TP-POE-2456D 24V Passive PoE to 802.3af/at converter. Converts 22V-36V passive PoE to 802.3af/at 35W output DATA SHEET

TP-POE-2456GD 24V Passive PoE to Gigabit 802.3af/at converter. Converts 22V-36V passive PoE to 802.3af/at 35W output DATA SHEET 

F-POE-G2

Optical Data Transport for Outdoor POE Devices

The FiberPoE connects remote PoE devices and provides data and power using fiber and DC cabling.

DATA SHEET

TP-SW5G-MULTI

Universal Multiple Voltage (MultiVolt™) 10/100/1000MB PoE Switch. Switch accepts up to 4 different voltages (12-57VDC) so user can power both 48V PoE and 24V PoE devices from the same switch. The port can individually be set to Data Only by disconnecting the voltage input to that specific port. 1A per port.

On the universal voltage models (“-NC”) the PoE output voltage = the input voltage so it is universal in its application. The Ethernet spec supports distances up to 100m (328 feet) between the PoE switch and the remote device.

Tycon Power® sells a variety of power supplies in 60W, 120W and 180W sizes. 18VDC, 24VDC and 48VDC are available. All the Switches have DIN Rail mounts included for convenient DIN rail mounting.

DATA SHEET

POE-48-24W-G

PoE Injector, 48VDC, 24W (RocketTi, UAP-Pro)

DATA SHEET

TP-VRHP-2456

Voltage Converter 18-36VDC Input, 56VDC @ 1.5A 70W Regulated output. 

The TP-VRHP-2456 is a 70W voltage converter/regulator which accepts an input of plus or minus +/-18VDC to 36VDC and provides a regulated output of 56VDC @ 1.25A 70W. These units are perfect for providing 56VDC voltage from -24VDC telecom power. Input and outputs are wire terminals for wire up to 12AWG. Operates from -30 to +65 deg C (-22 deg F to 149 deg F). 

DATA SHEET

USP-RPS

The UniFi SmartPower Redundant Power System, model USP-RPS, is a proprietary redundant power system designed to protect up to six UniFi SmartPower supported devices from sudden power supply module failure.

The USP-RPS continually monitors all attached devices. In the event of an internal AC/DC power supply failure, failover is automatic so your network continues to operate with no interruption in service. With a 950W DC power budget, the USP-RPS can protect a variety of high-power devices, including UniFi PoE switches. An integrated 1.3" color touchscreen LCM displays system information for convenient monitoring.

DATA SHEET

TP-DCDC-2424GR-VHP

The Gigabit compatible TP-DCDC-2424GR-VHP are special very high power DC to DC converters / PoE inserters designed especially for Ubiquiti airFiber x™ wireless radio systems and other systems which require high power passive PoE (High PoE). The unique PoE inserter supplies 24VDC PoE power on all 8 Ethernet wires (4 pair) with the following pinout: 1,2,4,5 V+ and 3,6,7,8 V

They have two isolated inputs for connecting 2 power sources, like a primary and backup power source. They have various protections for surge, short circuit and overload. The input and output are isolated.

DATA SHEET

TP-DCDC-1224 9-36VDC IN 24V PoE OUT 24W DC to DC Converter and PoE inserter DATA SHEET

TP-DCDC-1224G Gigabit 9-36VDC IN 24V PoE OUT 20W DC to DC Converter and PoE inserter DATA SHEET

TP-DCDC-1224G-4P Gigabit 9-36VDC IN 24VDC 4 Pair PoE OUT 24W DC to DC Converter and PoE inserter