PoE & Power Solutions

  • Show Sidebar

There are 69 products.

Active filters

TPDIN-MONITOR-WEB2

The TPDIN® Based Remote Monitor and Control System is a versatile tool which enables the equipment designer and installer to remotely monitor their equipment and site. The unit can be accessed via the network (web and SNMP) to remotely monitor up to 4 voltages, 4 currents, 2 temperatures and control power to various equipment using 4 on-board relays. The system has built-in surge protection to prevent damage from electrical surges.

DATA SHEET

TPW-400DT-12/24

The BreezePro® Wind Turbines from Tycon Solar® are lightweight at less than 10.5kg and are designed for ease of installation and long service life. The generator is a very low cogging force design for better performance in light winds and is packaged in a fully sealed die cast aluminum enclosure. There are no brushes to wear out or cause electrical noise and the bearings are sealed so the system is maintenance free. The blades are glass reinforced nylon for high strength, UV resistance and fatigue resistance. The turbines are 12V/24V auto voltage select.

DATA SHEET

PSDIN-48-240W

The PSDIN Series of Industrial DIN Rail mount high efficiency switching power supplies operate over a wide temperature range of -40C to +70C. There are two models to supply 120W or 240W. The input is 90 to 264VAC auto-ranging with wire terminal connections. The output is 48VDC nominal with an adjustment range from 47VDC to 56VDC. There is a switch for single or parallel operation. Two 240W supplies operating in parallel will provide 480W total power. There is an alarm output to provide a dry contact closure to trigger an alarm if the DC output fails, like during a grid power failure. The relay is closed when DC output is normal and open when DC output is in fault condition due to overload or safety shutdown.

DATA SHEET

TP-DCDC-2USB-24

USB Powered 24V Passive PoE inserter. 24VDC 12W Passive PoE Output with 2 USB power inputs. 10/100Mb.

The TP-DCDC-2USB-24 Passive Power Over Ethernet Power Source offered by Tycon Power Systems is a unique 24VDC Passive POE injector powered by two USB ports. They work by supplying power to the remote device on the 4 unused Ethernet pins 4,5(+) and 7,8(-). The Ethernet spec supports distances up to 100m (328 feet).

DATA SHEET

TP-DCDC-2USB-48

USB Powered 48V Passive PoE inserter. 48VDC 12W Passive PoE output with 2 USB power inputs. 10/100Mb

The TP-DCDC-2USB-48 Passive Power Over Ethernet Power Source offered by Tycon Power Systems is a unique 48VDC Passive PoE injector powered by two USB ports. They work by supplying power to the remote device on the 4 unused Ethernet pins 4,5(+) and 7,8(-). The Ethernet spec supports distances up to 100m (328 feet).

DATA SHEET

TP-POE-1824

48V 802.3af/at input, Switch Selectable 18V or 24V 12W passive PoE output. 10/100Mb. Converts 802.3af PoE to passive PoE.

802.3af/at Converter - Converts 48V 802.3af/at PoE to 18/24VDC (switchable) Passive PoE

The TP-POE-1824 Power Over Ethernet 802.3af/at converter is a unique product allowing a customer to run a Passive PoE device from a standard 802.3af or at PoE switch. They accept 802.3af/at PoE in and provide a switch selectable 12W PoE output of 18VDC or 24VDC.

DATA SHEET

TP-POE-1824G

48V 802.3af/at Gigabit input, Switch Selectable 18V or 24V 24W Gigabit passive PoE output. Converts 802.3af/at PoE to passive PoE.

The TP-POE-1824G Power Over Ethernet 802.3af/at converter is a unique product allowing a customer to run a Passive PoE device from a standard 802.3af or at PoE switch. They accept 802.3af/at PoE in and provide a switch selectable 24W PoE output of 18VDC or 24VDC.

DATA SHEET

TP-DCDC-1218

9-36VDC IN, 18V 18W Passive PoE OUT, DC to DC Converter/PoE inserter. 10/100Mb.

The TP-DCDC-1218 DC to DC converters offered by Tycon Power Systems are a low cost and high reliability solution for those requiring 18VDC Power Over Ethernet voltage from a 12 or 24V battery system. 

They have an integrated PoE injector to apply the regulated 18VDC to the CAT5 Ethernet cable. The input voltage must be between 9VDC and 36VDC.

DATA SHEET

TP-DCDC-1248 9-36VDC IN 48V PoE OUT 24W DC to DC Converter and PoE inserter DATA SHEET

TP-DCDC-1248-M 9-36VDC IN 48VDC OUT 24W DC to DC Converter and PoE inserter. Black Metal Enclosure. Industrial Applications. DATA SHEET

TP-DCDC-1248G Gigabit 9-36VDC IN 48V PoE OUT 24W DC to DC Converter and PoE inserter. DATA SHEET

TP-DCDC-1248D 9-36VDC IN 48VDC OUT 17W DC to DC Converter and 802.3af PoE inserter. DATA SHEET

TP-DCDC-1248GD Gigabit 9-36VDC IN 48VDC OUT 17W DC to DC Converter and 802.3af PoE inserter. DATA SHEET

TP-DCDC-1248GD-M Gigabit 9-36VDC IN 48VDC OUT 17W DC to DC Converter and 802.3af PoE inserter. Metal Enclosure. DATA SHEET

TP-DCDC-4824G

The TP-DCDC Gigabit Series of DC to DC converters offered by Tycon Power® are a low cost and high efficiency solution for those requiring IEEE802.3af or Passive Power over Ethernet from a 12VDC or 24VDC or 48VDC voltage source like a battery system or vehicle. They have an integrated POE injector to apply the power and data output to the CAT5 Ethernet cable. The output voltage is regulated and protected. They have two isolated inputs for connecting 2 power sources, like a primary and backup power source. A metal enclosure model is available for industrial applications.

DATA SHEET

TP-DCDC-4848GD

The TP-DCDC-4848GD Gigabit Series of DC to DC converters have an integrated Gigabit POE injector to apply the power and data output to the CAT5 Ethernet cable. The output voltage is regulated and protected. They have two isolated inputs for connecting 2 power sources, like a primary and backup power source. A metal enclosure model is available for industrial applications. They accept gigabit data-in to a shielded RJ45 Jack and provide gigabit data-out and PoE power on the shielded RJ45 output jack. They work by supplying power on the unused Ethernet pins 4,5(V+) and 7,8(V-). They have various protections for surge, short circuit and overload. The units have power outputs up to 17W.

DATA SHEET

TP-DCDC-1224-HP

The TP-DCDC-HP Series of DC to DC converters offered by Tycon Power® are a low cost and high reliability solution for those requiring 24VDC or 56VDC Power over Ethernet voltage from a 12V, 24V or 48V battery system. They have an integrated PoE injector. Passive PoE and 802.3at models are available.

The input and output are isolated so the units can accept minus voltage on input and can be wired for positive voltage on the output for those systems which are negative voltage based.

If the remote device does not support power over Ethernet, splitters (POE-SPLT-S) are available to split the data and DC voltage at the remote device. If the remote device requires reverse voltage the POE-XOVER-S cable can be used.

DATA SHEET

MTP250-26V94-OD

Outdoor IP67 26V 250W AC/DC power supply units for the MikroTik NetPower 16P. Built for situations when your outdoor switches need that extra juice. Pole/wall mount compatible!

DATA SHEET

MTP250-53V47-OD

Outdoor 53V 250W AC/DC power supply units for the MikroTik NetPower 16P. Built for situations when your outdoor switches need that extra juice. Pole/wall mount compatible!

DATA SHEET

TPDIN-MONITOR-WEB2

The TPDIN® Based Remote Monitor and Control System is a versatile tool which enables the equipment designer and installer to remotely monitor their equipment and site. The unit can be accessed via the network (web and SNMP) to remotely monitor up to 4 voltages, 4 currents, 2 temperatures and control power to various equipment using 4 on-board relays. The system has built-in surge protection to prevent damage from electrical surges.

DATA SHEET

TPW-400DT-12/24

The BreezePro® Wind Turbines from Tycon Solar® are lightweight at less than 10.5kg and are designed for ease of installation and long service life. The generator is a very low cogging force design for better performance in light winds and is packaged in a fully sealed die cast aluminum enclosure. There are no brushes to wear out or cause electrical noise and the bearings are sealed so the system is maintenance free. The blades are glass reinforced nylon for high strength, UV resistance and fatigue resistance. The turbines are 12V/24V auto voltage select.

DATA SHEET

PSDIN-48-240W

The PSDIN Series of Industrial DIN Rail mount high efficiency switching power supplies operate over a wide temperature range of -40C to +70C. There are two models to supply 120W or 240W. The input is 90 to 264VAC auto-ranging with wire terminal connections. The output is 48VDC nominal with an adjustment range from 47VDC to 56VDC. There is a switch for single or parallel operation. Two 240W supplies operating in parallel will provide 480W total power. There is an alarm output to provide a dry contact closure to trigger an alarm if the DC output fails, like during a grid power failure. The relay is closed when DC output is normal and open when DC output is in fault condition due to overload or safety shutdown.

DATA SHEET

TP-DCDC-2USB-24

USB Powered 24V Passive PoE inserter. 24VDC 12W Passive PoE Output with 2 USB power inputs. 10/100Mb.

The TP-DCDC-2USB-24 Passive Power Over Ethernet Power Source offered by Tycon Power Systems is a unique 24VDC Passive POE injector powered by two USB ports. They work by supplying power to the remote device on the 4 unused Ethernet pins 4,5(+) and 7,8(-). The Ethernet spec supports distances up to 100m (328 feet).

DATA SHEET

TP-DCDC-2USB-48

USB Powered 48V Passive PoE inserter. 48VDC 12W Passive PoE output with 2 USB power inputs. 10/100Mb

The TP-DCDC-2USB-48 Passive Power Over Ethernet Power Source offered by Tycon Power Systems is a unique 48VDC Passive PoE injector powered by two USB ports. They work by supplying power to the remote device on the 4 unused Ethernet pins 4,5(+) and 7,8(-). The Ethernet spec supports distances up to 100m (328 feet).

DATA SHEET

TP-POE-1824

48V 802.3af/at input, Switch Selectable 18V or 24V 12W passive PoE output. 10/100Mb. Converts 802.3af PoE to passive PoE.

802.3af/at Converter - Converts 48V 802.3af/at PoE to 18/24VDC (switchable) Passive PoE

The TP-POE-1824 Power Over Ethernet 802.3af/at converter is a unique product allowing a customer to run a Passive PoE device from a standard 802.3af or at PoE switch. They accept 802.3af/at PoE in and provide a switch selectable 12W PoE output of 18VDC or 24VDC.

DATA SHEET

TP-POE-1824G

48V 802.3af/at Gigabit input, Switch Selectable 18V or 24V 24W Gigabit passive PoE output. Converts 802.3af/at PoE to passive PoE.

The TP-POE-1824G Power Over Ethernet 802.3af/at converter is a unique product allowing a customer to run a Passive PoE device from a standard 802.3af or at PoE switch. They accept 802.3af/at PoE in and provide a switch selectable 24W PoE output of 18VDC or 24VDC.

DATA SHEET

TP-DCDC-1218

9-36VDC IN, 18V 18W Passive PoE OUT, DC to DC Converter/PoE inserter. 10/100Mb.

The TP-DCDC-1218 DC to DC converters offered by Tycon Power Systems are a low cost and high reliability solution for those requiring 18VDC Power Over Ethernet voltage from a 12 or 24V battery system. 

They have an integrated PoE injector to apply the regulated 18VDC to the CAT5 Ethernet cable. The input voltage must be between 9VDC and 36VDC.

DATA SHEET

TP-DCDC-1224 9-36VDC IN 24V PoE OUT 24W DC to DC Converter and PoE inserter DATA SHEET

TP-DCDC-1224G Gigabit 9-36VDC IN 24V PoE OUT 20W DC to DC Converter and PoE inserter DATA SHEET

TP-DCDC-1224G-4P Gigabit 9-36VDC IN 24VDC 4 Pair PoE OUT 24W DC to DC Converter and PoE inserter

TP-DCDC-1248 9-36VDC IN 48V PoE OUT 24W DC to DC Converter and PoE inserter DATA SHEET

TP-DCDC-1248-M 9-36VDC IN 48VDC OUT 24W DC to DC Converter and PoE inserter. Black Metal Enclosure. Industrial Applications. DATA SHEET

TP-DCDC-1248G Gigabit 9-36VDC IN 48V PoE OUT 24W DC to DC Converter and PoE inserter. DATA SHEET

TP-DCDC-1248D 9-36VDC IN 48VDC OUT 17W DC to DC Converter and 802.3af PoE inserter. DATA SHEET

TP-DCDC-1248GD Gigabit 9-36VDC IN 48VDC OUT 17W DC to DC Converter and 802.3af PoE inserter. DATA SHEET

TP-DCDC-1248GD-M Gigabit 9-36VDC IN 48VDC OUT 17W DC to DC Converter and 802.3af PoE inserter. Metal Enclosure. DATA SHEET

TP-DCDC-4824G

The TP-DCDC Gigabit Series of DC to DC converters offered by Tycon Power® are a low cost and high efficiency solution for those requiring IEEE802.3af or Passive Power over Ethernet from a 12VDC or 24VDC or 48VDC voltage source like a battery system or vehicle. They have an integrated POE injector to apply the power and data output to the CAT5 Ethernet cable. The output voltage is regulated and protected. They have two isolated inputs for connecting 2 power sources, like a primary and backup power source. A metal enclosure model is available for industrial applications.

DATA SHEET

TP-DCDC-4848GD

The TP-DCDC-4848GD Gigabit Series of DC to DC converters have an integrated Gigabit POE injector to apply the power and data output to the CAT5 Ethernet cable. The output voltage is regulated and protected. They have two isolated inputs for connecting 2 power sources, like a primary and backup power source. A metal enclosure model is available for industrial applications. They accept gigabit data-in to a shielded RJ45 Jack and provide gigabit data-out and PoE power on the shielded RJ45 output jack. They work by supplying power on the unused Ethernet pins 4,5(V+) and 7,8(V-). They have various protections for surge, short circuit and overload. The units have power outputs up to 17W.

DATA SHEET

TP-DCDC-1224-HP

The TP-DCDC-HP Series of DC to DC converters offered by Tycon Power® are a low cost and high reliability solution for those requiring 24VDC or 56VDC Power over Ethernet voltage from a 12V, 24V or 48V battery system. They have an integrated PoE injector. Passive PoE and 802.3at models are available.

The input and output are isolated so the units can accept minus voltage on input and can be wired for positive voltage on the output for those systems which are negative voltage based.

If the remote device does not support power over Ethernet, splitters (POE-SPLT-S) are available to split the data and DC voltage at the remote device. If the remote device requires reverse voltage the POE-XOVER-S cable can be used.

DATA SHEET